MakerBot Replicator 2 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro 3D tiskárny MakerBot Replicator 2. MakerBot Replicator 2 Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 2

10 B SETTING UP YOUR MAKERBOT REPLICATOR 2 DESKTOP 3D PRINTERFilament guide tubePower supply and cableHex wrenches PTFE-based greaseSpool holderUSB-

Strany 3 - TABLE OF CONTENTS

11B SETTING UP YOUR MAKERBOT REPLICATOR 2 DESKTOP 3D PRINTERMAKERBOT REPLICATOR 2 DIAGRAM8102113756491[1] GANTRY SYSTEM[2] LCD PANEL[3] KEY PAD[4] TH

Strany 4 - Let’s get started

12UNPACKING YOUR MAKERBOT REPLICATOR 21a. Place the MakerBot Replicator 2 box on the ground. Open the box and remove the top cardboard sheet.1b. Remov

Strany 5

13UNPACKING YOUR MAKERBOT REPLICATOR 2 CONTINUED3a. Remove the two remaining protective foam pieces from the bottom of the Replicator 2’s box.3b. Li

Strany 6 - SPECIFICATIONS

14INSTALLING BUILD PLATEB SETTING UP YOUR MAKERBOT REPLICATOR 2 DESKTOP 3D PRINTER5a. Use strong scissors or a wire cutter to cut the zip ties holdin

Strany 7 - HOW DOES IT WORK?

15INSTALLING FILAMENT GUIDE TUBE AND SPOOL HOLDERB SETTING UP YOUR MAKERBOT REPLICATOR 2 DESKTOP 3D PRINTER6a. Locate the filament guide tube. Insert

Strany 8 - Desktop 3D Printer

16MOUNTING FILAMENT SPOOL AND ATTACHING USB CABLE9a. Locate the USB-A to USB-B cable. Insert the USB cable into the USB-B port on the back of the Mak

Strany 9

10a. Locate the power supply and cable. Attach the cable to the power supply.10b. Ensure that the power switch on the MakerBot Replicator 2 is set to

Strany 10 - WHAT’S IN THE BOX

Startup Process: Leveling, Loading, TestingC

Strany 11 - MAKERBOT REPLICATOR 2 DIAGRAM

19THE LCD KEYPAD• Four arrow buttons surround a central M button. Use the arrows to navigate through the LCD menus and make selections.• The le arr

Strany 13 - Removing the Accessory Box 1

20Aer the initial welcome message, the Startup Script will display the following:• If the build platform is too far from the extruder nozzle, or if

Strany 14 - INSTALLING BUILD PLATE

21LEVELING THE BUILD PLATE CONTINUEDC STARTUP PROCESS: LEVELING, LOADING, TESTINGLevelingKnobsSupportCardWhen directed by the LCD screen, tighten e

Strany 15 - Installing the Spool Holder

22LEVELING THE BUILD PLATE CONTINUEDC STARTUP PROCESS: LEVELING, LOADING, TESTINGThe script will prompt you to adjust the knobs individually. As yo

Strany 16 - Mounting the Filament Spool

23LOADING MAKERBOT PLA FILAMENT C STARTUP PROCESS: LEVELING, LOADING, TESTINGWhen you have completed the initial leveling tasks, the LCD menu will di

Strany 17 - Attaching the Power Supply

24LOADING MAKERBOT PLA FILAMENT CONTINUEDFree the end of the MakerBot PLA Filament from the filament spool. With a pair of scissors, cut a clean edge

Strany 18 - Loading

25C STARTUP PROCESS: LEVELING, LOADING, TESTINGAer you’ve fed the MakerBot PLA Filament all the way through the guide tube, press the M button on th

Strany 19 - THE LCD KEYPAD

26Take the end of the MakerBot PLA Filament closest to the extruder and firmly push it into the hole in the top of the extruder. Ensure that the filamen

Strany 20 - LEVELING THE BUILD PLATE

27C STARTUP PROCESS: LEVELING, LOADING, TESTINGPush the guide tube back into the opening on the top of the extruder.NOTE: If you have problems or nee

Strany 21 - CONTINUED

28 C STARTUP PROCESS: LEVELING, LOADING, TESTINGAer you have successfully leveled the build platform and loaded the MakerBot PLA Filament into the

Strany 22 - Confirm your Adjustment

29C STARTUP PROCESS: LEVELING, LOADING, TESTINGMAKING A TEST OBJECT FROM THE SD CARD CONTINUEDProjects Available on the SD CardCHAIN LINKSFile Name

Strany 23 - What You Will Do

A WELCOME. LET’S GET STARTED 04 Specifications 06 How Does it Work? 07 B SETTING UP YOUR MAKERBOT REPLICATOR 2 DESKTOP 3D PRINTER 08 What’s in T

Strany 24

Making an Object with MakerBot MakerWareD

Strany 25 - Press the M to Continue

31How to make an object using a computer and MakerBot® MakerWare™.D MAKING AN OBJECT WITH MAKERBOT MAKERWARE™

Strany 26 - Stop Extrusion

32USING MAKERBOT MAKERWARED MAKING AN OBJECT WITH MAKERBOT MAKERWARE1c. Open the installer and follow the directions to install the soware.1d. Use t

Strany 27 - Remove the Extruded PLA

33Thingiverse is a website where MakerBot users and others can share design files.2a. Open a browser session and go to www.thingiverse.com. Use the sea

Strany 28 - Locate the SD Card

34USING MAKERBOT MAKERWARE CONTINUED3Open MakerBot MakerWare[1] CAMERA HOME: Resets MakerWare to the default view of the object.[2] +/-: Zoom in a

Strany 29 - Space for

35USING MAKERBOT MAKERWARE CONTINUED3Open MakerBot MakerWare | Continued1 2 7 8 9 10113645D MAKING AN OBJECT WITH MAKERBOT MAKERWARENUT AND BO

Strany 30 - MakerBot MakerWare

Minimalist NYC buildings Design By: JonMonaghan Thingiverse: 12762364a. Click on the Add button. Navigate to the location of the file FlatIron.stl and

Strany 31 - MakerWare

374e. Click on the Flatiron Building to select it. Hold down the shi key and click on the Woolworth Building. Then release the shi key. Both models

Strany 32 - USING MAKERBOT MAKERWARE

38TIP: If you plan to build from an SD card instead of directly from MakerWare, select “Export to a File” at the top of the Make dialog instead of “Ma

Strany 33

5c. Accept the default settings and click the Make It! button. MakerWare will slice your model and send it to your MakerBot Replicator 2 for building.

Strany 34 - Open MakerBot MakerWare

Welcome. Let’s get started.A

Strany 35

ETroubleshooting, Diagnostics, and Maintenance

Strany 36

41This chapter describes basic troubleshooting and maintenance tasks for your MakerBot® Replicator®2 Desktop 3D Printer. For details on more advanced

Strany 37 - Save and Make Your file

Can’t load MakerBot PLA Filament into the extruder Make a fresh cut at the end of the MakerBot PLA Filament. Cut the MakerBot PLA Filament at an angl

Strany 38

PROBLEM SOLUTION43E TROUBLESHOOTING, DIAGNOSTICS, AND MAINTENANCETROUBLESHOOTING CONTINUEDCan’t remove MakerBot PLA Filament from extruderObject w

Strany 39 - USING REPLICATORG

44 E TROUBLESHOOTING, DIAGNOSTICS, AND MAINTENANCEDIAGNOSTICS LCD PANEL | TOP-LEVEL MENUBUILD FROM SD Displays the list of models on the SD ca

Strany 40 - Maintenance

45E TROUBLESHOOTING, DIAGNOSTICS, AND MAINTENANCEUTILITIESMonitor ModeDisplays the current temperature of the extruder. When making an object, displa

Strany 41

46 E TROUBLESHOOTING, DIAGNOSTICS, AND MAINTENANCEINFO AND SETTINGSBot StatisticsDisplays the estimated total hours and minutes of building in the li

Strany 42

47E TROUBLESHOOTING, DIAGNOSTICS, AND MAINTENANCEMAINTENANCEAer approximately 50 hours of build time, you should lubricate the threaded rod on your

Strany 43 - TROUBLESHOOTING CONTINUED

48 E TROUBLESHOOTING, DIAGNOSTICS, AND MAINTENANCELubricating the Threaded Rod and the X-Axis Idler Pulley | Continued7. Locate the X-axis idler

Strany 44 - TROUBLESHOOTING CONTINUED

49E TROUBLESHOOTING, DIAGNOSTICS, AND MAINTENANCEMAINTENANCE CONTINUEDCleaning the Drive GearThe drive gear is the part of the extruder that pushes

Strany 45

05WARNING: The MakerBot Replicator 2 generates high temperatures and includes moving parts that can cause injury. Never reach inside the MakerBot Repl

Strany 46

50 E TROUBLESHOOTING, DIAGNOSTICS, AND MAINTENANCEMAINTENANCE CONTINUEDCleaning the Drive Gear | Continued6. Reseat the motor assembly.7. Plug

Strany 47 - MAINTENANCE

51E TROUBLESHOOTING, DIAGNOSTICS, AND MAINTENANCEMAINTENANCE CONTINUEDAdjusting the PlungerIf you are having trouble building things, you might nee

Strany 48 - MAINTENANCE CONTINUED

52 E TROUBLESHOOTING, DIAGNOSTICS, AND MAINTENANCEMAINTENANCE CONTINUEDAdjusting the Plunger | Continued2. Aer you’ve removed the screws, mov

Strany 49

ACTIVE COOLING FAN: The fan that cools the MakerBot PLA Filament as it extrudes.BLUE TAPE: Blue masking tape that makes a great build surface for o

Strany 50

MOTOR ASSEMBLY: The stepper motor and the drive block that push filament into the extruder.MOTOR WIRES: The bundle of electrical wires that provide p

Strany 51

CONTACT US55E TROUBLESHOOTING, DIAGNOSTICS, AND MAINTENANCESUPPORTSALESFEEDBACKmakerbot.com/supportOur website has extensive documentation and troubl

Strany 52

56 F TERMS OF SERVICETERMS OF SERVICEPlease read these Terms of Service (“Terms”) carefully before using this Website or ordering from MakerBot Indus

Strany 53 - GLOSSARY OF TERMS

57F TERMS OF SERVICETERMS OF SERVICE CONTINUEDattributes than those listed, or may actually carry a dierent price than that stated on this Website

Strany 54 - GLOSSARY OF TERMS CONTINUED

58 F TERMS OF SERVICEtransmission, disclosure, publication, broadcast, development, manufacturing and/or marketing in any manner whatsoever for any o

Strany 55 - CONTACT US

equipment, or other property caused by or arising from your access to, use of, or browsing this Website, or your downloading of any information or mat

Strany 56 - TERMS OF SERVICE

06 A WELCOME, LET’S GET STARTEDPRINTING Print Technology: Fused Filament FabricationBuild Volume: 11.2 L x 6.0 W x 6.1 H in [28.5 x 15.3 x 15.5 c

Strany 57 - TERMS OF SERVICE CONTINUED

MakerBot One MetroTech Center, 21st Floor, Brooklyn, NY [email protected] makerbot.com

Strany 58

07A WELCOME, LET’S GET STARTEDThe MakerBot Replicator 2 makes solid, three-dimensional objects out of melted MakerBot PLA Filament. Your 3D design fil

Strany 59

Setting Up Your MakerBot® Replicator®2 Desktop 3D PrinterB

Strany 60

09When you set up your MakerBot® Replicator®2Desktop 3D Printer, remember that it was built and packaged very carefully at the MakerBot factory. We ho

Komentáře k této Příručce

Žádné komentáře